Provided links give access to illustrations and/or additional information. To return to this page use your browser back button.
ORIENTATION FOR STACK OR SYSTEM ASSEMBLY
When assembling equipment, operators sometimes find it necessary or advantageous to join flanged equipment of different nominal size or working pressure. Adapter Flanges or Adapter Spools necessary for this may have a different number of bolt holes on their opposite connections. When this case occurs, a problem of proper orientation presents itself. API 6A, 19th Edition contains the following. "10.5.4.2.7 Bolt Location For Flanges. A pair of bolt holes in both end flanges shall straddle the referring centerline." This design requirement assures that operators can maintain a proper orientation of equipment if they understand this requirement and how it applies to field assembly.
The following illustrations will make clear a method of recognizing the points of common center line that will assure proper orientation of the next piece of equipment joined in an assembly.
BOLT CIRCLE LAYOUT, FLANGED ADAPTER SPOOL
BOLT CIRCLE LAYOUT,
DOUBLE STUDDED ADAPTER
This Double Studded Adapter with 12 studs extending from one connection and 8 studs extending from the other will have 4 points around its circumference where two studs in each connection will straddle a common centerline.
Although they have different configurations, both the Flanged Adapter Spool and the Double Studded Adapter illustrated conform to the API Spec 6A requirement for bolt circle orientation (Single Studded Adapters, not illustrated also conform).
Persons making an assembly of flanged equipment should visually identify the 4 common center lines on all pieces of equipment. Maintaining strict alignment of this set of center lines through any assembly that requires an adapter will assure predictable orientation of the next connected unit.
Note: When adapters built to API Spec 6A requirements have the same number of holes, or studs, on each connection, all of these holes will straddle common center lines. The orientation of such an adapter does not effect the orientation of the next equipment connected. As a general rule any outlet connection on a Spool or Blowout Preventer will fall on the same center lines as the connection bolt holes. Except for special requirements outlets project at 90° from the Run bore and two outlets, 180° apart.
The following illustrations provide examples of bolt hole arrangement and outlet position on different types of Well Head and Blowout Preventer equipment.
BOLT CIRCLE LAYOUT, BLOWOUT PREVENTER (BOP)
BOLT CIRCLE LAYOUT, STUDDED TEE AND CROSS
BOLT CIRCLE LAYOUT, FLANGED TEE AND CROSS
BOLT CIRCLE LAYOUT, FLANGED GATE VALVE
As an example of a problem situation, observe the following illustration of an out of orientation installation made for a Flow Line connection extending to a Studded Cross in a Choke Manifold.
REFERENCE TO CENTER LINE OF BOP EQUIPMENT
The above illustration shows a 7-1/16" 5M x 4-1/16" 5M Flanged Adapter Spool installed without proper reference to center lines. An attempt to install a Studded or Flanged Cross onto any Spacer Spool extending from the 4-1/16" 5M flange will result in cross outlets 30° out of level plane. Unless the operator intended this orientation, disassembly and reassembly must take place.
If persons making assemblies using adapters do not have awareness of this information, they may consume valuable operator time investigating a non-existent, but suspected, equipment defect.
For more information aboutjoining equipment units having differing flange connections, see Crossover Connections and Double Drilled Flanges.
Information above, and in other
parts of this Web Site, may help persons who really seek to know. If you
have a question, and you think WOODCO USA may have the capacity to answer
it, please use our
Contact Us link and give us a
chance to help.
WOODCO USA provides Web Site Tools for identification, estimating, and reference only. Do not use this information for manufacturing or inspection. Users of these tools should not use them as a substitute for professional engineering advice. Anyone making use of the information presented does so at his own risk and assumes any and all liability resulting from such use.
FOR FURTHER INFORMATION, OR TO LEARN MORE ABOUT WOODCO USA PRODUCTS AND SERVICES,